AutoTalkShowFirst, change Taiqian what to do?
secure parking
After the discovery of the vehicle tire puncture or leak, do not panic, and do not stop in the middle of the road, open the double flash immediately move the vehicle to the roadside or emergency lane, try to choose a flat road, avoid turning on or slope parking, until the vehicle is parked, pull up the handbrake turn off.
Note: Be sure not strong distraction to enchant tire repair shop, because as the leak rate, it will be possible to continue driving the whole scrap tires!
When should immediately confirm the safety warning triangle is laid out.
Triangle location, on the rear of the vehicle 50-150 meters from the location, and if the highway will have to put in place 150 meters after the car; in low visibility or at night in the rain and fog weather, the need to set up warning signs 100 meters after the car place.
Check Tool
After the above steps are completed, followed by inspection of the jack and the onboard tool kit and a spare tire is complete, can be used normally. Need to check whether the vehicle has parking stall, stall has been linked to a P position (neutral manual model), the hand brake has been re-tensioned, this is to ensure that the vehicle does not induce accidents during changing of the tire.
Note: Do not think that is necessarily spare tire intact, taking a trip to see the best, otherwise problems can only cry.
Replacement tires several commonly used tool is the jack screws rocker, rocker arms and other help.
Second, the flow change tires
removing a tire
Jacks do not immediately put in removing the tire from the roof when the rocker arm must be screws with screws one by unscrewing the wheel, when unscrewing the bolts, one by unscrewing diagonal methods to be employed, this is In order to prevent uneven force deformed fastener.
Note: should pay attention to removing the fixing screw force direction of the wheel: Loosen the counterclockwise direction; clockwise to tighten.
This process is generally gray often painful (Hercules automatically ignore), because the screws tighten the wheel tight, so we can make use of body strength (see repair shop so you are using a power tool to screw up and down) I go with this tool too pit of it.
Remember rocker arm screws and screw position must be aligned stuck, or the body hard slippery, broken tools. And on some models are also equipped with anti-theft bolts, then use the original car with a special anti-theft bolts caps set up in order to be caught wrench, loosen the bolts just a little, but do not put all the bolts unscrewed.
jack of use
Loosen all the bolts after the vehicle can be raised (Note: Not lifting the front of the vehicle just loosen). Before raising the vehicle, first looking for jack support position, the frame support points every car is different, most carmakers are usually made to identify the body at the appropriate location, easy to find people, and if I can not find it can only climb down a touch. (Find criterion is: Find the most rigid assembly connected to the vehicle body)
Must be used with the jack: in general, both sides will be the bottom of the vehicle jack corresponding slot, the slot in the jack attention to avoid accidents.
Use jack rising vehicle speed is not too fast, so as to avoid the risk of instability due to the support vehicle from sliding off the jack occur. The tire body to hold up off the ground, leaving about a mean position of nearly all of the bolts can be removed to loosen, do not rise to a high spirits, after loading the tire when avoid trouble.
install the spare tire
The most strenuous mounted spare tire is how to align the spare tire and wheel fixing bolt hole, preferably with the help of others, if a person with the operation of the proposed against the spare tire to prevent displacement of the legs or feet, and then followed by a diagonal bolts slightly tighten.
Do a breath screwed note that when the tire equipment, but still in the order of a diagonal line of tightening turns, and preferably the number of turns of each screw is screwed consistent during screwing, in order to ensure a uniform force screws .
Screwed criteria to remove just the opposite with, just before the pretension jack pine. After the jack pine is strongly tightened.
Finally, do not forget the spare tire of the vehicle if not a full-size spare tire, just a temporary spare tire, it should as soon as possible to find the nearest service point or tire shop to replace the conventional tire, the maximum speed can not exceed 80km/h, the travel distance can not be longer than 150 km non-full-size spare tire slippery, do not do hard acceleration, braking and sharp turns, as slower speed driving, safety first is important.
Toss down, palm to become a black lake. So remember to put on a glove in the trunk.
Summary: On the spare tire replacement work can be counted on is a manual labor, no small amount of exercise, but also to change a tire requires a certain skill, you could drive a friend for a long time will come again, but I'm afraid if afraid of ten thousand in case of emergency is not to rush, as a novice should practice the process of changing a tire, "their hands and clothing" thing.