In order to secure the car, please carefully read the tutorial painted Hide

Precautions

1, a brush machine to prepare their own notebook data line and Windows systems OBD.

3, turn off the computer before installing the software antivirus software, 360 will be manslaughter.

(BMW communication protocol software is included in the window can not be identified, so there may be anti-virus software false positives. But it is not a virus, do riders have been brushed, ease of use, remember to turn off antivirus software!)

4, brush during vehicle to be powered not ignite. Will check the vehicle before writing off, do not write a power failure. Notebook also charged

(Do not park the vehicle after a few days brush, brush the battery voltage is not enough, the first car ignition 10 minutes before charging case on the brush)

5, if pop prompt (list index out of bounds), which is a software error, the first point OK, and then disconnect point software, and finally exit the software and restart the software to

6, brushing memory if the situation can not turn off air conditioning air conditioning appears, wait ten minutes (or driving a few kilometers) to return to normal.

7, the same module to hide, you can write all at once changing for the better. Not different modules to change were well written.

In general: all modules changing for the better, and then exit the software, start the car.

For example: CAS/FEM_BODY/BDC_BODY module has memory and start and stop delay lock car folding mirrors, these two functions may be changing for the better, respectively, and then to write-once. Brush and then to the next module

Nine Steps brush hidden

1, double-click to run the self-extracting software package (extract password: ych) of! And open BMWAiCoder.exe

2, the top left tab, select ENET

3, vehicle detection

4, connected vehicles

5, get a list of ECU

6, by reading the selection module is selected from

7, modify the parameters (digital modification, adjustment shall take effect keyboard Enter)

8. Press to write

9, Disconnect

1, extract and open BMWAICoder.exe (the desktop shortcut can also be generated, this folder location C drive YCH folder)

2, the top left ENET selected, then in step 1234 according to FIG connection list and reads the vehicle ECU

3, the ECU acquires a list, click-click modules reading below, then the corresponding parameter modification, last written. Repeat this brush in different modules. (Red or black module name word inoperable module, do or read operation).

Please reference the other cars, where the name of the module function much the same, according to the reference to find,

Brush features require hardware support: USB video playback needs NBT host, EVO is supported, the knob can be handwritten, support for DVD playback is NBT Host

Folding mirrors need original car comes power folding mirror functions (not electric control)

When sustained in case of detection can not detect vehicles

Summary question:

1: When there can not detect a vehicle (as shown below), please check the computer prompts and vehicle settings according to the software;

1) anti-virus software and firewall needs to close. Vehicle needs energization state, i.e. not press brakes ignition key.

2) Check the connection: to Control Panel - Network Connections - left there is a change adapters - click on the go - see Ethernet

A If it is crossed-out state, indicating that the car and the laptop is not connected, check whether the data line two plug steady, firmly seated

B if not crossed state, indicating that the car and the computer has been connected, right - property -Internet Protocol version 4 Double-click - to automatic acquisition. IP address is set to automatically obtain and then try to detect vehicles

C If that does not work, click local connection - right - disabled, and then enabled. And then try to detect vehicles, if the computer is connected to a wireless network at this time, disconnect

3) does not work, restart the computer, shut the door after the car 10 minutes and try again.

4) or not, it is recommended to reinstall the network card driver, or a computer system. Or try to replace notebook

2: Software error

When reading to a module, the software will have the opportunity to error.

After clicking OK, select the upper left corner of the software is disconnected, turn off the upper right corner of the software re-open the software - detection - Connection - Get a list ECU, heavy brush can be.

3: write failed, 1: first to increase the timing to try again, if not enough. 2: terminate the task ignition charge ten minutes. Restore painted

About backup recovery

When you want to restore a module, click on the small green knob can recover, under no small green knob, there is no backup file

After a good brush to hide, disconnect the test vehicle, the software will save the folder where the file is no problem well. (7 in which the frame number file named backup file folder for vehicle)

1,2,3,4,5,7 Department (parameter | pictures) OBD plug location

X-based plug location

With a hidden module can write all at once changing for the better. Not different modules to change were well written.

In general: all modules changing for the better, and then exit the software, start the car.

For example: CAS/FEM_BODY/BDC_BODY module has memory and start and stop delay lock car folding mirrors, these two functions may be changing for the better, respectively, and then to write-once. Brush and then to the next module

After a good brush to hide, disconnect the test vehicle, the software will save the folder where the file is no problem well. (In which seven named file folder frame number for the vehicle backup file) folder in the C drive is a position folder YCH